GFCI-state-adoptions

What is GFCI protection?

Ground-fault circuit interrupter (GFCI) protection is a type of home electrical safety system.
  • A special GFCI breaker or electrical outlet can sense imbalances in an electrical branch circuit and shut off power to that circuit in time to prevent a person from being shocked or electrocuted.
  • A single GFCI breaker can protect all electrical devices connected to the circuit it protects.
  • A single GFCI electrical outlet on a circuit can protect all the devices downstream from it.
  • Installing GFCI protection is relatively inexpensive.

Modern Required Locations

For many jurisdictions, the required locations are specified by the National Electric Code (NEC).

Jurisdictional requirements can vary because the NEC is updated every 3 years, but because it's expensive,  jurisdictions don't always adopt the most recent version.

All 125-volt through 250-volt receptacles installed in the locations specified in 210.8(A)(1) through (A)(11) and supplied by single-phase branch circuits rated 150 volts or less to ground shall have ground-fault circuit-interrupter protection for personnel.

  1. Bathrooms
  2. Garages and also accessory buildings that have a floor located at or below grade level not intended as habitable rooms and limited to storage areas, work areas, and areas of similar use
  3. Outdoors
    Exception to (3): Receptacles that are not readily accessible and are supplied by a branch circuit dedicated to electric snow-melting, deicing, or pipeline and vessel heating equipment shall be permitted to be installed in accordance with 426.28 or 427.22, as applicable.
  4. Crawl spaces — at or below grade level
  5. Basements
    Exception to (5): A receptacle supplying only a permanently installed fire alarm or burglar alarm system shall not be required to have ground-fault circuit-interrupter protection.
    Informational Note: See 760.41(B) and 760.121(B) for power supply requirements for fire alarm systems.
    Receptacles installed under the exception to 210.8(A)(5) shall not be considered as meeting the requirements of 210.52(G).
  6. Kitchens — where the receptacles are installed to serve the countertop surfaces
  7. Sinks — where receptacles are installed within 1.8 m (6 ft) from the top inside edge of the bowl of the sink
  8. Boathouses
  9. Bathtubs or shower stalls — where receptacles are installed within 1.8 m (6 ft) of the outside edge of the bathtub or shower stall
  10. Laundry areas
    Exception to (1) through (3), (5) through (8), and (10): Listed locking support and mounting receptacles utilized in combination with compatible attachment fittings installed for the purpose of serving a ceiling luminaire or ceiling fan shall not be required to be ground-fault circuit-interrupter protected. If a general-purpose convenience receptacle is integral to the ceiling luminaire or ceiling fan, GFCI protection shall be provided.
  11. Indoor damp and wet locations

Testing Receptacle-Type GFCIs

Inspectors should test GFCI protection using the buttons on the GFCI receptacles. If you use the trip button on your tester, you may hear the reset button click at a receptacle located behind a mountain of boxes stacked against a wall, all of which will have to be moved to reset the circuit, or the homeowner and both agents may be unhappy with you!
If the "RESET" button pops out but the light does not turn off, the GFCI has been improperly wired. Contact an electrician to correct the wiring errors. 

If the "RESET" button does not pop out, the GFCI is defective and should be replaced.

If the GFCI is functioning properly and the lamp turns off, press the "RESET" button to restore power to the outlet.
Note!  When testing for GFCI protection of electrical circuits by activating the trip button on a 3-light testing device, the inspector may then be unable to locate the GFCI outlet controlling the circuit to which he has shut off power. Affected outlets are sometimes in another part of the home or hidden behind the occupant’s belongings. Using the test button built into GFCI outlets will prevent this problem.
Recognizing GFCI Breakers
GFCI breakers are easy to recognize by the additional white conductor and the label.